Home>Heating>Blowers


MSR903 (click on pic for dimensional line drawing)

The MSR Model 903HC is the heater of choice for mounting on the face of a cabinet or other compartment. This blower is equpped with an air purge. This air vent fitting is opened and closed with a small flat blade screwdriver. This small part is the answer for the common problem or air venting on hot water heating system start-up.
Specifications:
Voltage: 12 VDC or 24 VDC
BTU Rating: 7,000 BTU @180 degree F water temperature at 3 G.P.M.


Model 005-302 Fan Heater.  3,500 BTU @ 180 F 3 GPM Flow

Designed specifically for heating of a small compartment similar to an Marine head compartment or small stateroom.  3” ducting and air outlet grill can be extended into those tight locations on a boat. 
Built in air vent and standard 3/4” water system connections.
Optional MPT or PEX solder fitting & two speed switch are available.  Complete with heater, ducting, clamps and air grill.

Height  :  4.125”
Width   :  6”
Depth   :  8”             12 or 24V Models available  

 


Model 005-905FF Fan Heater 8,000 BTU @ 180 F 3 GPM flow
Dual 2.5” air outlets allow heating of two adjacent small staterooms or stateroom and marine head compartment. The 2.5” flexible ducting can be extended into and past those small access openings.
The two air flow adjustable air grills allows heating balance at a touch of the air flow louver.  Built in air vent and standard 3/4” water system connections. Optional MPT or PEX solder fitting & two speed switch are available.  Complete with heater, ducting, clamps and air grills. FF features allows multiple  heater position for ducting and hose routing.
Height  :  5.75”
Width    :  7”
Depth    : 8.5”          12 or 24V Models available


\

Model 005-914FF fan Heater 8,000 BTU @ 180F 3 GPM flow.
This four inch duct and air grill equipped heater provides quiet even heat in the sleeping area and other areas.  In field air flow direction change is possible.  Remove 4 screws on the front and back reverse the motor and air outlet and the front will be come the back with air flow in the opposite direction.  No need for 180 degree duct routing to get the air pointed in the right directions. Built in air vent and standard 3/4” water system connections. Optional MPT or PEX solder fitting & two speed switch are available.  Complete with heater, ducting, clamp and air grill.     Height  :  5.75”
Width    :  7”
Depth    : 8.5”          12 or 24V Models available


Model 005-919FF fan heater  8,000 BTU @ 180F 3 GPM flow

This heater equipped with three inch duct and air grill will fit into those location where the four inch ducting cannot fit.  Similar equipped as the Models 005-905FF & 914FF for in-field motor Air outlet air flow direction.  These FF Models can also be rotated 180 degrees so the top becomes the bottom for water hose routing with out the need for hose cross over.  Dual air vent fittings allow this feature. The Models 905FF,914FF & 919FF are all equipped with a five pass water coil for superior water flow & heat output.

Height  :  5.75”
Width    :  7”
Depth    : 8.5”          12 or 24V Models available

MSR Model 005-909II cabinet toe space mounting fan heater.

Five pass water coil for 7,000 BTU rating. Black anodized aluminum cutout cover air grill.  Low profile (3.75”) allows installation in a cabinets toe space or other low profile location.  Ideal heater for galley space Installation for “Warm Feet” for the first mate for morning coffee or meal  preparation.  Heater can also be mounted vertical in those narrow unused space on some cabinets.
12 or 24V Models available

 

MSR Model 005-941FF Single 4” air outlet fan heater.

Five pass water coil for 16,500 BTU rating with dual 12V .36A fans.  Complete with ducting, duct clamps & air outlet  grill.  Ideal fan heater for large cabin heat utilizing space saving single duct & air outlet grill.
FF models allows hose routing and connection from either side of the mounting compartment..
12 or 24V Models available

 

MSR Model 005-942FF Dual 4” air outlet fan heater.

Five pass water coil for 16,500 BTU rating with dual 12V .36A fans.  Complete with ducting, duct clamps & air outlet  grills.  Ideal fan heater for large cabin heat utilizing dual outlets for even heat circulation. 
FF models allows hose routing and connection from either side of the mounting compartment..
12 or 24V Models available

 

MSR Model 005-942-C 

Combination windshield defrost with four 2” outlets and single 4” outlet for helm station heat from one fan heater.  High capacity squirrel cage 3 speed motor  for high air movement for windshield defrost and single quiet low amperage fan  for helm station heat from one heater.
Heater is equipped with ducting, 2 & 3 speed switch and air Outlet grills.
12 or 24V Models available

 

MSR Model 005-930 Fan Heater

Single 4” outlet duct system
D&W 4” Adjustable air flow Direction Grill
5’ flexible 4” ducting with plastic duct clamps
MSR 005-711 3 speed switch & mount plate
3/4” hose connection (special order 5/8” or “PEX” adapter
Dimensions
6” High • 9” Wide • 11.5” Deep           25,000 BTU 170F Water Temp @ 3 GPM flow

 

MSR Model 005-932 Fan Heater  

Dual 3”  outlet duct system Two 3” 
Adjustable air flow Direction Grill 10’
flexible 3” ducting with duct clamps
MSR 005-711 3 speed switch & mount plate 3/4” hose connection (special order 5/8” or “PEX” adapter)
Dimensions
6” High • 9” Wide • 11.5” Deep           25,000 BTU 170F Water Temp @ 3 GPM flow

 

MSR Model 005-933 Fan Heater  

Three 2 1/2”  outlet duct system
Three 2 1/2”  Adjustable air flow Direction
Grill 15’ flexible 2 1/2”  ducting with  duct clamps
MSR 005-711 3 speed switch & mount plate 3/4” hose connection (special order 5/8” or “PEX” adapter) Dimensions
6” High • 9” Wide • 11.5” Deep           25,000 BTU 170F Water Temp @ 3 GPM flow

MSR Model 005-934 Fan Heater

Four 2 1/2”  outlet duct system
Four 2 1/2”  Adjustable air flow Direction
Grill 20’ flexible 2 1/2” ducting with duct clamps
Dimensions
6” High • 9” Wide • 11.5” Deep           25,000 BTU 170F Water Temp @ 3 GPM flow

 

Bracket for mounting MSR heaters to Bulkhead

© copyright 2006 River Marine Supplies and Distributors 1023 Clark Drive, Vancouver, B.C. Canada V5L 3K1